17-4 PH Stainless Steel 630
ASTM A564 Alloy 17-4 PH AISI 630 is a precipitation hardening martensitic stainless steel with Cu additions. The grade combines high strength, hardness (up to 300°C / 572°F) and corrosion resistance, combining …
Datasheet 15-5 PH STAINLESS STEEL – AMS 5659
15-5 PH stainless steel is a martensitic precipitation-hardening stainless steel with approximately 15% Chromium and 5% Nickel. It has high strength, high hardness, and excellent corrosion resistance. Strength can be further increased by a single low temperature heat treatment. Compared to 17-4 PH, it offers better transverse toughness …
ASTM-A564
ASTM-A564 Standard Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes ... To find similar documents by ASTM Volume: 01.03 (Steel--Plate, Sheet, Strip, Wire; Stainless Steel Bar) To find similar documents by classification: 77.140.60 (Steel bars and rods)
SS 17-4 PH | UNS S17400 | ASTM A564
T630 is a 17-4 PH martensitic precipitation hardening stainless steel with a unique combination of high strength and good corrosive resistance. Supplied in either the H1075 (H580) aged condition with a tensile strength of 1000 Mpa minimum (HB 311 min.), or the H1150 (H620) double aged condition with a tensile strength of 930 Mpa minimum (HB …
Astm A564 | PDF | Heat Treating | Forging
NOTE 3—A typical ordering description is as follows: 5000 lb [2270 kg] Type 630, Solution-Annealed Cold Finished Centerless Ground, 11⁄2 in. 6. Chemical Composition. [38.0 mm] round bar, 10 to 12 ft [3.0 to 3.6 m] in length, ASTM A 564 6.1 Each alloy covered by this specification shall conform to.
Technical Data Sheet
ASTM A564 ASTM SA-564. Bars, Wire and Shapes . ASTM A693 ASME SA-693. Sheet, Plate and Strip . ASTM A705 ASME SA-705. Forgings . PRODUCT FORMS. ATI 17-4™ precipitation hardening stainless steel is furn ished as plate, sheet, strip and long products. In all forms, the material is
ASTM A564 Specification 17-4PH Stainless Steel | Aero-Vac
Stainless Steel Rings. 16 Cr, 4.0 Ni, 0.30 Cb Ta, 4.0 Cu. 17-4PH Stainless Steel in ASTM A564 Specification, per ASTM International: "This specification covers bars and shapes of age-hardening stainless steels. Hot-finished or cold-finished rounds, squares, hexagons, bar shapes, angles, tees, and channels are included.
Stainless Steel Grade Custom 465 | UNS# S46500
General corrosion resistance is similar to type 304 and its strength is superior to Custom 455. Stainless Steel Custom 465 Specifications: AMS 5936. ASTM A564, ASTM F899. Stainless Steel Grade Custom 465 product forms offered at all Titanium Industries' locations: Stainless Steel Grade Custom 465 Round Bar. Buy Now.
Steel Standards
A660/A660M-21 Standard Specification for Centrifugally Cast Carbon Steel Pipe for High-Temperature Service. A781/A781M-21 Standard Specification for Castings, Steel and Alloy, Common Requirements, for General Industrial Use. A487/A487M-21 Standard Specification for Steel Castings Suitable for Pressure Service.
Stainless Steel
The properties mentioned below pertain to commonly available grade 630 bar products in ASTM A564. The specifications may not be similar to other forms such as forgings and plates. Composition. The compositional ranges of grade 630 stainless steels are displayed below: Table 1. Composition ranges for grade 630 stainless steels
Astm A564
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee. A01.17 on Flat-Rolled and Wrought Stainless Steel. Current edition approved Oct. 1, 2010. Published October 2010. Originally. approved in 1966. Last previous edition approved in 2009 as A564/. A564M 04 (2009).
ASTM A564 Specification
90 rowsASTM A564 Specification. This specification2 covers bars and shapes of agehardening stainless steels. Hot-finished or cold-finished rounds, squares, hexagons, …
ASTM A564 / 1.4542 MATERIAL DATA SHEET
ASTM A564 / 1.4542 MATERIAL 17-4PH stainless steel offers extreme resistance against corrosion, whether it is intergranular corrosion, stress-corrosion cracking, or corrosion fatigue. Covering a wide temperature range from cryogenic to more than 320 °C, 17-4PH is a versatile material for aerospace and space, (petro-)chemical, and medical ...
ASTM A564 Properties (Chem., Mech. & Rankings) 2022
ASTM A564 is a Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes. Category Corrosion-Resisting and Heat-Resisting Steels Scope This specification covers bars and shapes of age hardening stainless steels. Hot-finished or cold-finished rounds, squares, hexagons, bar shapes, …
UNS S45500 (Alloy 455, XM-16) Stainless Steel
S45500 stainless steel is a precipitation-hardening stainless steel formulated for primary forming into wrought products. XM-16 is the ASTM designation for this material. S45500 is the UNS number. And Alloy 455 is the common industry name. It has a moderately high embodied energy among wrought precipitation-hardening stainless steels.
Stainless Steel Grades Overview | Vested Metals
410 is a general-purpose stainless steel. It is usually used for applications where mild corrosion, heat resistance, and high strength are expected to be encountered. 410 is an air hardening steel containing 12% chromium. It …
Valve Materials of Construction Part 1
o ASTM A351 Grade CF8M (316 SS) o ASTM A351 Grade CF3M (316L SS) –lower C (0.03%) o ASTM A351 Grade CF8C (347 SS) –H2 services • Major Technical Advantages: o Corrosion Resistance o Toughness at Low Temperature (Cryogenic) o Oxygen Service o Clean Services • Alloy 20 (UNS N08020) –Niobium added, used for sulfuric acid service
MATERIAL DATASHEET 17-4 PH Stainless Steel
ASTM A564 H900 Heat Treated ASTM A564 17-4 PH stainless steel heat treated to H900 specification. MIM H900 Heat Treated 17-4 PH MIM standard stainless steel heat treated to H900 specification. REV 2.0 - 7/25/2018 Tensile Stress MPa Strain 0 200 400 600 800 1000 1200 1400 0 0.02 0.04 0.06 0.08 0.10 MIM 1 PH SS rouht 1 PH SS Marore 1 PH SS
Standard Specification for General Requirements for …
ASTM specifications: A276/A276M, A314, A458, A477, A479/A479M, A564/A564M, A565/A565M, A582/A582M, A638/A638M, A705/A705M, and A831/A831M. 1.2 In the case of conflict between a requirement of a ... A564/A564M Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes
ASTM A564 Stainless Steel Flat Bars
When it comes to ASTM A564 Stainless Steel Flat Bars, you can count on Grainger. Supplies and solutions for every industry, plus easy ordering, fast delivery and 24/7 …
Material Specifications for Stainless Steel | Stainless Shapes
38./46. 1.5/3.0. Ti .60/1.20 Al .20 Fe 22.0 min. NM. Stainless Shapes provides detailed specs for stainless steel grades. Ideal for industrial needs. Contact us today for a quote today.
Standard Specification for Hot-Rolled and Cold-Finished …
in 1966. Last previous edition approved in 2010 as A564/A564M – 10. DOI: 10.1520/A0564_A0564M-13. 2 For ASME Boiler and Pressure Vessel Code applications, see related Specifi-cation SA-564/SA-564M in Section II of that Code. 3 For referenced ASTM standards, visit the ASTM website,, or contact ASTM Customer …
ASTM A564 / 1.4545 MATERIAL DATA SHEET
ASTM A564 / 1.4545 MATERIAL 15-5PH stainless steel is based on the chemistry of 17-4PH, but with slight modifications leading to minimal contents of delta ferrite leading to …
ASTM A564/A564M : Standard Specification for Hot …
ASTM A564/A564M, Revision 19A, September 1, 2019 - Standard Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and …
Chemical Composition ( ASTM A564 Type 630 / 1.4542 / …
ASTM A564 is a standard material specification for hot-rolled and cold-finished age-hardening stainless steel bars, including type 630 / UNS S17400 / 17-4 PH used for parts requiring corrosion resistance and high strength at room temperature, or at temperatures up to 600°F [315°C]. Boltport uses S17400 round bars to ASTM this specification to ...
Custom 465® Advanced Stainless Flexible for Many …
Custom 465 alloy is currently covered by the MMPDS-02, AMS 5936, and ASTM A564 specifications. Custom 465 stainless can be considered as a corrosion resistant replacement for 300M, AISI 4340, and similar types of steels that must be plated or otherwise surface coated to provide corrosion resistance.
Alloy 465 /Custom 465 / UNS S46500/ AMS 5936
ASTM A693 ASTM A564 ASTM F899 MMPDS-01 UNS S46500. For more information about Custom 465 for use in medical applications, visit our medical division at Customer Reviews - What Customers Say About Us! "Just wanted to say thanks for your efforts and updates"
Standard Specification for Hot-Rolled and Cold-Finished …
2.1 ASTM Standards:3 A 314 Specification for Stainless Steel Billets and Bars for Forging A 370 Test Methods and Definitions for MechanicalTesting of Steel Products A 484/A …
Stainless Steel 17-4 PH or ASTM A564 (630)
17-4PH / 1.4542 / S17400Precipitation Hardening Martensitic Stainless Steel. Stainless Steel 17-4 PH is a precipitation-hardening martensitic stainless steel that is widely used in a variety of applications due to its high strength, corrosion resistance, and excellent toughness. It is also known as ASTM A564 (630), which is the specification ...
ASM Material Data Sheet
AISI Type S15500 (15Cr-5Ni) Precipitation Hardening Stainless Steel transverse direction, intermediate location, condition H1150. Subcategory: Ferrous Metal; Metal; Precipitation Hardening Stainless; Stainless Steel; T S10000 Series Stainless Steel Key Words: 15-5 PH, 15-5PH, 15/5 PH, 15/5PH, XM12, AMS 5862, ASME SA705 (XM-12), ASTM A564 (XM …
AMS 5659 Stainless Steel
ASTM A564 (Grade XM-12) ASTM A705 (Grade XM-12) ASME SA564; Boeing BMS 7-240; Boeing BMS 7-351; SPP Canada Aircraft SPPCA-EN-SOW-0036 (Capability) Liebherr LAT 1-9037; AMS-STD-2154 (Ultrasonic Inspection) AMS 5659 Uses. AMS 5659 sheets is used in various applications that require high strength, toughness, …
17-4PH, H1150D, ASTM A564, Double 열처리 : 네이버 블로그
1150℉ 에서 두번 열처리를 해. H1150 + H1150 으로도 표기합니다. 17-4PH 에서 17-4는 Chromium 17%. Nickel 4% 수준의 합금량을 말하고,Cu 4% 합금입니다. 17-4PH에서 PH는 석출 경화 (precipitation hardening) 강재임을 나타내고, 17-4PH, H1150D 강재는. 내식성에서는 304 강재와 비슷한 ...
Stainless Steel
A time-honoredmedical material. medical material. Stainless steel is the most basic medical material. It's also the first material we ever drew into wire at Fort Wayne Metals. We begin the stainless steel drawing process with our carbide dies for diameters greater than 2.54 mm [0.100 in]. From there, we transition to our polycrystalline dies ...